Vehicle Relearn
The following information must be followed carefully to allow the vehicle to correctly learn the new sensor IDs:
Relearn Type: OBDII
Set tyre pressure
Read all sensor IDs
Turn ignition ON (engine on) by using Hands-free key card (with key-less entry system)
Connect the OBDII Cable/Module to OBD connector
Follow the screens instructions to reset the ECU
Turn ignition to OFF then ON (engine off)
Wait for 20 min
NOTICE: If the TPMS warning light remains ON, drive for 20 min
OBDII Port Location*
*The location shown is for left-hand drive vehicles.
Relearn Type: DEALER-ONLY
The vehicle must be returned to the dealership to complete the relearn.
| Make | Renault |
|---|---|
| Model | Laguna 3 |
| Model Code | X91 |
| Date of Manufacture | 2007 |
| OE Sensor Manufacturer | CONTINENTAL |
| OE Sensor Number | 407000435R |
| OE Sensor Description |
Choose a sensor type:
CON-S027
VDO TG1C Clamp-In Sensor
OE_SENSSensorVDOOriginal EquipmentBarcode: 5055563000238
Comparative Parts: CON-S027, 72-20-024, 4035, 65939-67, 5055563000238, TECHCON-S027,
VDO TG1C OE replacement sensor.
CON-S027.Z
VDO TG1C Clamp-In Sensor
OE_SENSSensorVDOContinentalOriginal EquipmentBarcode: 5055563000238
Comparative Parts: CON-S027.Z, 72-20-024, 4035, 65939-67, 5055563000238, TECHCON-S027.Z,
SCH-S535
Schrader Pre-Programmed EZ Delta Clamp-In Sensor
OE_SENSSensorSchraderOriginal EquipmentBarcode:
Comparative Parts: SCH-S535, 72-22-047, 73-22-047, HSCH-S535, T2200-GO,
Other Programmable Sensors
ALI-S113
Alligator Sens.It Clamp-In Sensor 433MHz
SensorAlligatorBarcode: 5055563003345
Comparative Parts: ALI-S113, 72-20-085, 73-20-085, HALI-S113, 590914, 5055563003345, 5624000,
Alligator programmable Sens.It sensor 433Mhz.
Requires a TPMS diagnostic tool to program the sensor for a particular vehicle.
ALI-S114
Alligator Sens.It Snap-In Sensor 433MHz
SensorAlligatorBarcode: 5055563003352
Comparative Parts: ALI-S114, 72-20-086, 73-20-086, HALI-S114, 590918, 5055563003352, 5624002,
Alligator programmable Sens.It sensor 433Mhz.
Requires a TPMS diagnostic tool to program the sensor for a particular vehicle.
HUF-S559
Intellisens Clamp-In Sensor
SensorHufBarcode:
Comparative Parts: HUF-S559, 72-21-958, 73-21-958, HHUF-S559,
HUF-S560
Intellisens Snap-In Sensor
SensorHufBarcode:
Comparative Parts: HUF-S560, 72-21-959, 73-21-959, HHUF-S560,
SCH-S163
Schrader EZ 2.0 Snap-In Sensor - EU 433Mhz
SensorSchraderBarcode: 5055563005516
Comparative Parts: SCH-S163, 72-20-844, 73-20-844, HSCH-S163, 1210, 5055563005516,
SCH-S164
Schrader Delta EZ 2.0 Clamp-In Sensor - EU 433Mhz
SensorSchraderBarcode: 5055563005523
Comparative Parts: SCH-S164, 72-20-845, 73-20-845, HSCH-S164, 2200, 5055563005523,
Schrader programmable EZ-Sensor 2.0 433Mhz EU.
Requires a TPMS diagnostic tool to program the sensor for a particular vehicle.
SCH-S165
Schrader Faraday EZ 2.0 Clamp-In Sensor - EU 433Mhz
SensorSchraderBarcode: 5055563005530
Comparative Parts: SCH-S165, 72-20-846, 73-20-846, HSCH-S165, 2210, 5055563005530,
Click an image to show the correct service parts for that type:
Service Parts For: VDO TG1C Clamp-In Sensor
Show Products With Tags:
AM Parts
TYR-V006_10
Box Of 10 Replacement Clamp-In Valves for VDO TG1C
Most Popular ValveVDOAM PartBarcode: 6924478980739
Comparative Parts:
A box of 10 clamp-in valves, with each including: 1 Valve Stem and 1 Valve Cap.
These valves are suitable for use with VDO TG1C type sensors.
TYR-V006_10
Box Of 10 Replacement Clamp-In Valves for VDO TG1C
ValveVDOAM PartBarcode: 6924478980739
Comparative Parts:
A box of 10 clamp-in valves, with each including: 1 Valve Stem and 1 Valve Cap.
These valves are suitable for use with VDO TG1C type sensors.
TYR-K008_10
Box Of 10 Service Kits for VDO TG1C
Service KitVDOAM PartBarcode: 6924478980609
Comparative Parts:
A box of 10 service kits, with each including: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
TYR-K010_10
Box Of 10 Service Kits for VDO TG1C
Service KitVDOAM PartBarcode: 6924478980623
Comparative Parts:
A box of 10 service kits, with each including: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
TYR-K013_10
Box Of 10 Service Kits for VDO TG1C
Service KitVDOAM PartBarcode: 6924478961493
Comparative Parts:
A box of service kits, with each including: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core and 4 Rings.
These service kits are suitable for use with VDO TG1C type sensors.
TYR-V053_10
Box Of 10 Replacement Clamp-In Valves for VDO TG1C
ValveVDOAM PartBarcode: 6924478981071
Comparative Parts:
A box of 10 clamp-in valves, with each including: 1 Valve Stem, 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
These valves are suitable for use with VDO TG1C type sensors.
TYR-K008_10
Box Of 10 Service Kits for VDO TG1C
Service KitVDOAM PartBarcode: 6924478980609
Comparative Parts:
A box of 10 service kits, with each including: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
TYR-K010_10
Box Of 10 Service Kits for VDO TG1C
Service KitVDOAM PartBarcode: 6924478980623
Comparative Parts:
A box of 10 service kits, with each including: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
TYR-K013_10
Box Of 10 Service Kits for VDO TG1C
Service KitVDOAM PartBarcode: 6924478961493
Comparative Parts:
A box of service kits, with each including: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core and 4 Rings.
These service kits are suitable for use with VDO TG1C type sensors.
TYR-V053_10
Box Of 10 Replacement Clamp-In Valves for VDO TG1C
ValveVDOAM PartBarcode: 6924478981071
Comparative Parts:
A box of 10 clamp-in valves, with each including: 1 Valve Stem, 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
These valves are suitable for use with VDO TG1C type sensors.
OE Parts
SCH-V006_10
Box Of 10 Clamp-In Valves for VDO TG1C
ValveVDOOE PartBarcode: 5055563001525
Comparative Parts:
A box of 10 Schrader clamp-in valves, with each including: 1 Valve Stem and 1 Valve Cap .
These valves are suitable for use with VDO TG1C type sensors.
SCH-V006_10
Box Of 10 Clamp-In Valves for VDO TG1C
ValveVDOOE PartBarcode: 5055563001525
Comparative Parts:
A box of 10 Schrader clamp-in valves, with each including: 1 Valve Stem and 1 Valve Cap .
These valves are suitable for use with VDO TG1C type sensors.
CON-K008
Service Kit for VDO TG1C
Service KitVDOOE PartBarcode: 5055563000726
Comparative Parts:
A single VDO service kit, which includes: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
CON-K010
Service Kit for VDO TG1C
Service KitVDOOE PartBarcode: 5055563000740
Comparative Parts:
A single VDO service kit, which includes: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
CON-K013
Service Kit for VDO TG1C
Service KitVDOContinentalOE PartBarcode: 5055563000702
Comparative Parts:
A single VDO service kit, which includes: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap, 1 Valve Core and 4 Rings.
This service kit is suitable for use with VDO TG1C type sensors.
CON-K008
Service Kit for VDO TG1C
Service KitVDOOE PartBarcode: 5055563000726
Comparative Parts:
A single VDO service kit, which includes: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
CON-K010
Service Kit for VDO TG1C
Service KitVDOOE PartBarcode: 5055563000740
Comparative Parts:
A single VDO service kit, which includes: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap and 1 Valve Core.
This service kit is suitable for use with VDO TG1C type sensors.
CON-K013
Service Kit for VDO TG1C
Service KitVDOContinentalOE PartBarcode: 5055563000702
Comparative Parts:
A single VDO service kit, which includes: 1 Nut, 1 Rubber Grommet, 1 Metal Washer, 1 Valve Cap, 1 Valve Core and 4 Rings.
This service kit is suitable for use with VDO TG1C type sensors.
Service Parts For: Schrader Pre-Programmed EZ Delta Clamp-In Sensor
Show Products With Tags:
AM Parts
TYR-V022_10
Box Of 10 Replacement Clamp-In Valves for Schrader Gen Gamma
Most Popular ValveSchraderAM PartBarcode: 6924478962353
Comparative Parts:
A box of 10 clamp-in valves, with each including: 1 Valve Stem, 1 Nut, 1 Rubber Grommet, 1 Plastic Washer, 1 Valve Cap and 1 Valve Core.
These valves are suitable for use with Schrader Gen Gamma and Schrader Gen Delta type sensors.
